Page 15 - ISCAR FACE GROOVING LINES

PICCO-010/610 CDX OAL IC228
(Face Grooving) OHN
Inserts for Face Grooving DCONMS FACE GROOVE-TURN

DAXN a CDX
CW CW OHN

INCH Right-hand shown
Dimensions
Recommended
Designation DAXN(1) CW CDX DCONMS a OHN(2) OAL Machining Data

PICCO R 010.1006-10 .24 .039 .059 .236 .205 .433 1.024 f face-groove
(IPR)
PICCO R 010.1506-10 .24 .059 .079 .236 .205 .433 1.024
• .0004-.0016
PICCO R 010.1008-10 .31 .039 .059 .276 .232 .433 1.024 • .0004-.0016
• .0004-.0016
PICCO R 010.1008-20 .31 .039 .059 .276 .232 .827 1.378 • .0004-.0016
• .0004-.0016
PICCO R 010.1008-30 .31 .039 .059 .276 .232 1.181 1.772 • .0004-.0016
• .0004-.0016
PICCO R 610.1008-10 .31 .039 .059 .236 .205 .433 1.024 • .0004-.0016
• .0004-.0016
PICCO R 610.1008-20 .31 .039 .059 .236 .205 .787 1.378 • .0004-.0016
• .0004-.0016
PICCO R/L 010.1508-20 .31 .059 .098 .276 .232 .827 1.378 • .0004-.0016
• .0008-.0020
PICCO R/L 010.1508-30 .31 .059 .098 .276 .232 1.181 1.772 • .0008-.0020
• .0008-.0020
PICCO R 010.1508-10 .31 .059 .098 .276 .232 .433 1.024 • .0008-.0020
• .0008-.0020
PICCO R 610.1508-10 .31 .059 .098 .236 .205 .433 1.024 • .0008-.0020
• .0008-.0020
PICCO R 610.1508-20 .31 .059 .098 .236 .205 .787 1.378 • .0008-.0020
• .0008-.0020
PICCO R/L 010.2008-30 .31 .079 .118 .276 .232 1.181 1.772 • .0008-.0020
• .0008-.0024
PICCO R 010.2008-10 .31 .079 .118 .276 .232 .433 1.024 • .0008-.0024
• .0008-.0024
PICCO R 010.2008-20 .31 .079 .118 .276 .232 .827 1.378 • .0008-.0024
• .0008-.0024
PICCO R 610.2008-10 .31 .079 .118 .236 .205 .433 1.024

PICCO R 610.2008-20 .31 .079 .118 .236 .205 .787 1.378

PICCO R 010.2508-10 .31 .098 .138 .276 .232 .433 1.024

PICCO R 010.2508-20 .31 .098 .138 .276 .232 .827 1.378

PICCO R 010.2508-30 .31 .098 .138 .276 .232 1.181 1.772

PICCO R 610.2508-10 .31 .098 .138 .236 .205 .433 1.024

PICCO R 610.2508-20 .31 .098 .138 .236 .205 .787 1.378

PICCO R 010.3008-10 .31 .118 .138 .276 .232 .433 1.024

PICCO R 010.3008-20 .31 .118 .138 .276 .232 .827 1.378

PICCO R 010.3008-30 .31 .118 .138 .276 .232 1.181 1.772

PICCO R 610.3008-10 .31 .118 .138 .236 .205 .433 1.024

PICCO R 610.3008-20 .31 .118 .138 .236 .205 .787 1.378

• Only right-hand inserts are available as standard • All inserts are with sharp corners • For detailed cutting data, see pages 162-164

(1) Minimum axial grooving diameter

(2) Minimum overhang

13