Page 15 - TURNING CATALOG p255-458
P. 15
DGFH-JHP CUTDIA CWN-CWX GROOVE-TURN
Parting and Grooving Blades
with Channels for Low and Min. Max.
High-Pressure Coolant
Carrying DO-GRIP Inserts HF H
WB
Min. Max. WB_2
OAL
Bar Max
Designation CWN(2) CWX(3) WB WB_2 OAL H HF CUTDIA Insert
DGFH 32-2-JHP (1) 1.90 (4) 2.50 1.80 2.5 150.00 32.0 24.8 39.0 DG. 1.../DG. 2... SGC 340 EDG 33A-JHP*
DGFH 32-3-JHP 3.00 (4) 3.18 2.50 - 152.00 32.0 24.8 90.0 DG. 1.../DG. 3... SR M2.0X2.5DIN916 SGC 340 EDG 33A-JHP*
4.00 4.00 3.20 - 152.00 32.0 24.9 90.0 DG. 4.../GRIP 4... SR M2.0X2.5DIN916 SGC 340 EDG 33A-JHP*
DGFH 32-4-JHP 5.00 5.00 4.00 - 152.00 32.0 24.9 90.0 DG. 5.../GRIP 5... SR M2.0X2.5DIN916 SGC 340 EDG 33A-JHP*
6.00 6.35 5.20 - 160.00 32.0 24.9 90.0 DG. 6.../GRIP 6... SGC 340 EDG 33A-JHP*
DGFH 32-5-JHP
DGFH 32-6-JHP (1)
• For user guide and accessories, see pages 419-436
(1) Only an upper channel
(2) Minimum cutting width
(3) Maximum cutting width
(4) For DG. 1... insert, modify holder
* Optional, should be ordered separately
For inserts, see pages: DGN-LF/LFT (485) • DGN-MF (485) • DGN-P (487) • DGN-UT/UA (487) • DGN-W (482) • DGN-WP (488) • DGN-Z (486)
• DGN/DGNC/DGNM-C (481) • DGN/DGNM-J/JS/JT (483) • DGR-P (488) • DGR-WP (488) • DGR-Z/ZS (486) • DGR/L-C DGRC/LC-C (482)
• DGR/L-J/JS (484) • GRIP (269) • GRIP (full radius) (270)
For holders, see pages: TGTBU-JHP (497)
GRIP INSL (Ref.) No depth penetration limit
Utility Double-Ended ±0.1
Inserts for External, Internal Recommended Machining Data
and Face Machining RE BW
CW
Dimensions
Tough 1 Hard
IC830 ap f turn f groove f face-
IC8250 groove f face-turn
Designation CW RE CWTOL(1) RETOL(2) INSL BW IC08 (mm) (mm/rev) (mm/rev)
IC808 (mm/rev) (mm/rev)
GRIP 3002Y IC908 0.08-0.20 0.10-0.20
GRIP 3003Y IC418 0.08-0.20 0.10-0.20
GRIP 318-040Y IC5010 0.08-0.20 0.10-0.20
GRIP 4002Y IC806 0.10-0.24 0.15-0.30
GRIP 4004Y IC807 0.10-0.24 0.15-0.30
GRIP 476-080Y IC804 0.10-0.24 0.15-0.30
GRIP 5005Y 0.12-0.24 0.15-0.35
GRIP 5008Y 3.00 0.20 0.05 0.050 15.80 2.30 • • • • • • • • 0.25-1.80 0.14-0.18 0.07-0.11 0.12-0.24 0.15-0.35
GRIP 6005Y 0.050 15.80 2.30 • • • • • • • • 0.12-0.28 0.15-0.40
GRIP 6008Y 3.00 0.30 0.05 0.050 15.80 2.30 • ••• • 0.40-1.80 0.15-0.19 0.07-0.11 0.12-0.28 0.15-0.40
GRIP 635-080Y 0.12-0.28 0.15-0.40
3.18 0.40 0.05 0.050 19.00 2.80 • • • • • •• 0.50-1.90 0.17-0.22 0.07-0.12
4.00 0.20 0.05 0.25-2.40 0.16-0.21 0.09-0.14
0.050 19.00 2.80 • • • • • • • • • • 0.50-2.40 0.18-0.24 0.09-0.15
4.00 0.40 0.05 0.050 19.00 3.10 • • ••• •
4.76 0.80 0.05 1.00-2.80 0.21-0.33 0.10-0.20
0.050 19.00 3.30 • • • • • • • • • • 0.60-3.00 0.20-0.30 0.11-0.20
5.00 0.50 0.05 0.050 19.00 3.40 • • ••••••
5.00 0.80 0.05 0.050 19.00 4.20 • • •••••• 1.00-3.00 0.23-0.35 0.11-0.21
6.00 0.50 0.05 0.050 19.00 4.20 • • •••••• 0.60-3.60 0.22-0.36 0.13-0.23
6.00 0.80 0.05 0.050 19.00 4.20 • • • • • 1.00-3.60 0.24-0.42 0.13-0.25
6.35 0.80 0.05 1.00-3.80 0.25-0.44 0.14-0.27
• For cutting speed recommendations and user guide, see pages 419-428, 432-436
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)
For tools, see pages: C#-HELIR/L (265) • C#-HFIR/L-MC (573) • CR HFIR-M (575) • D/HGAD RE/LE-JHP (499) • DGAD/HGAD (479)
• DGFH (268) • DGFH-JHP (269) • DGFS (469) • DGTR/L (476) • HELIIR/L (355) • HELIR/L (266) • HFAER/L-4 (565) • HFAER/L-5T, 6T (566)
• HFAIR/L-4 (572) • HFAIR/L-DG (573) • HFFR/L-T (564) • HFHR/L-4T (559) • HFHR/L-5T (560) • HFIR/L-MC (574) • HFPAD-3 (562)
• HFPAD-4 (563) • HFPAD-5 (563) • HFPAD-6 (564) • HFPAD-JHP (562) • HGAER/L-3 (565) • HGAIR/L-3 (568) • HGFH (268) • HGHR/L-3 (558)
• HGPAD (267) • HGPAD-JHP (267) • IM-HFIR-MC (574)
The Twisted Insert
for Face Machining
The double-ended, twisted insert body
makes it possible to machine deeper than
the insert’s length.
A unique chipformer for controlled chip flow
in axial and radial directions.
The rear angle is slanted in relation
to the frontal edge so it does not
come into contact with the machined
groove surface as the tool penetrates
deeply into the workpiece.
269
