Page 17 - ISCAR FACE GROOVING LINES

PICCO-010 OAL IC1008
(Round Face Groove)
Inserts for Round Profile a CDX DCONMS FACE GROOVE-TURN
Face Grooving CW OHN DAXN

METRIC Right-hand shown
Dimensions
Recommended
Machining Data

Designation DAXN(1) CW RE CDX DCONMS a OHN(2) OAL f face-groove
(mm/rev)
PICCO R 010.1005-10 8.0 1.00 0.50 2.00 7.00 5.90 11.0 26.00 • 0.01-0.04
PICCO R 010.1005-20 8.0 1.00 20.0 35.00 • 0.01-0.04
PICCO R 010.1608-10 8.0 1.60 0.50 2.00 7.00 5.90 11.0 26.00 • 0.01-0.05
PICCO R 010.1608-20 8.0 1.60 20.0 35.00 • 0.01-0.05
PICCO R 010.2010-10 8.0 2.00 0.80 3.00 7.00 5.90 11.0 26.00 • 0.02-0.05
PICCO R 010.2010-20 8.0 2.00 20.0 35.00 • 0.02-0.05
PICCO R 010.2512-10 8.0 2.50 0.80 3.00 7.00 5.90 11.0 26.00 • 0.02-0.05
PICCO R 010.2512-20 8.0 2.50 20.0 35.00 • 0.02-0.05
PICCO R 010.3015-10 8.0 3.00 1.00 4.00 7.00 5.90 11.0 26.00 • 0.02-0.05
PICCO R 010.3015-20 8.0 3.00 20.0 35.00 • 0.02-0.05
1.00 4.00 7.00 5.90
Recommended
1.25 5.00 7.00 5.90 Machining Data

1.25 5.00 7.00 5.90

1.50 6.00 7.00 5.90

1.50 6.00 7.00 5.90

INCH

Dimensions

Designation DAXN(1) CW RE CDX DCONMS a OHN(2) OAL IC1008 f face-groove

PICCO R 010.1005-10 .31 .039 .0197 .079 .276 .232 .433 1.024 • (IPR)
PICCO R 010.1005-20 .31 .039 .0197 .079 .276 .232 .787 1.378 • .0004-.0016
PICCO R 010.1608-10 .31 .063 .0315 .118 .276 .232 .433 1.024 • .0004-.0016
PICCO R 010.1608-20 .31 .063 .0315 .118 .276 .232 .787 1.378 • .0004-.0020
1.024 • .0004-.0020
PICCO R 010.2010-10 .31 .079 .0394 .157 .276 .232 .433 1.378 • .0008-.0020
PICCO R 010.2010-20 .31 .079 .0394 .157 .276 .232 .787 1.024 • .0008-.0020
PICCO R 010.2512-10 .31 .098 .0492 .197 .276 .232 .433 1.378 • .0008-.0020
PICCO R 010.2512-20 .31 .098 .0492 .197 .276 .232 .787 1.024 • .0008-.0020
PICCO R 010.3015-10 .31 .118 .0590 .236 .276 .232 .433 1.378 • .0008-.0020
PICCO R 010.3015-20 .31 .118 .0590 .236 .276 .232 .787 .0008-.0020

• Only right-hand inserts are available as standard, left-hand inserts on request • For detailed cutting data, see pages 162-164

(1) Minimum axial grooving diameter

(2) Minimum overhang

15